Analysis of corrugated box equipment in North Chin

2022-08-06
  • Detail

Analysis of corrugated box equipment in North China (II)

corrugated board production line

North China is firmly at the top of the corrugated board production line in North China with a proportion of 29%, followed by 17% Liaoning, 15% Beijing, 13% Tianjin and 10% Jilin, followed by Heilongjiang and Shanxi, both of which are 8%. Hebei is a big packaging province. There are many local corrugated board production enterprises that have recently ushered in a new opportunity line for five gold tool torque testing equipment. Most of their products are produced and sold by themselves, which basically meets the needs of local users, that is to say, their localization is relatively high. However, a problem with the local corrugated board production line is that there are too many low-grade products, which can not meet the requirements of high-end users. Therefore, the urgent task is to improve the product grade, develop to high-end products, and strive to make it difficult to cut plates such as vacuum insulation board on site to meet the needs of more users

the proportion of corrugated board production lines in North China's provinces (municipalities directly under the central government) is mostly in the mainland, accounting for more than 80% of the whole. However, in Beijing and Tianjin, the proportion of machinery in Taiwan, China also accounts for about 15%, which is closely related to the degree of economic development of the two municipalities directly under the central government. With the increasing demand of the pharmaceutical and fruit industries in North China, the proportion of machinery in Taiwan, China, Europe, the United States and Japan will gradually increase. That is to say, North China has great development potential and broad market prospects

the speed of corrugated board production lines in Beijing and Tianjin from 100m to 200m/min accounts for 18% and 16% respectively, and the speed of corrugated board production lines above 200m/min can also account for about 8%. However, the speed proportion of corrugated board production lines in the whole North China is still below 1o0m/sheet, mainly because most of them use mainland machines, and the speed is relatively slow

since all the machines in this area were added in the early stage, the mainstream is below 1.8m, and only Beijing can account for 14% of the total in the range of 1.8m ~ 2.2m. The startup rate is kept between 60% and 80%, of which the highest is 78% in Heilongjiang and the lowest is 58% in Jilin. The absolute number of corrugated board production lines in North China is small, so the startup rate is higher than that in other regions

situation of plate making machines

the number of plate making machines in Hebei ranks first in North China, accounting for 27%, followed by Tianjin, accounting for 22%, and Liaoning Gu; Il is less in Beijing, accounting for 19% and 13%. Plate making machines are mainly produced in the mainland. In Beijing, Tianjin and Heilongjiang, European, American and Japanese products also account for a certain share, which are 16%, 13% and 12% respectively. In other regions, European, American and Japanese products account for a small share, of which Shanxi uses mainland equipment

engraving machine situation

engraving machine Hebei reaches 24% at most, Shanxi and Jilin are at least single digits, and other provinces and cities are basically flat at around 15%. Engraving machines are basically made in China

situation of proofing machines

the number of proofing machines in Beijing and Tianjin is the largest, 29% and 28% respectively. Hebei and Heilongjiang account for 16% and 1l The proportion of other provinces and cities is about 5%. The proofing machine is a high-end product, so it is dominated by Europe, the United States and Japan nationwide. This law is also followed in North China, especially in Tianjin, where European, American and Japanese products account for 88% of the total, ranking first in the region. Mainland machines, such as stretching, zigzag, impact and hardness, also occupy a place, mostly around 18%, of which Beijing is on the high side, up to 25%

situation of plate washing machines

the proportion of plate washing machines in Jilin, Beijing and Tianjin is about 15%, and that in Hebei is 18%. Even in Liaoning, where the proportion is as high as 25%, there is still a big gap compared with 30% ~ 40% in South China. However, the overall gap in the proportion of plate washing machines in North China is not very large, and it is in a state of balanced development. This is obviously different from the large drop range in South China and East China

the place of origin of plate washing machines is mainly in the mainland, which is most obvious in Jilin. All plate washing machines in this region are made in China. European, American and Japanese products also account for a considerable share, especially more than 20% in Beijing and Hebei

printing machine situation

Liaoning and Hebei have the highest proportion of printing machines, 21% and 19% respectively; Tianjin, Heilongjiang and Beijing are all around 15%; Shanxi and Jilin are relatively low, and the proportion is in single digits. In general, the proportion of plate printers in North China is low, mainly because plate making machines, plate washing machines and plate printers are supporting products, and the low utilization rate of the former two equipment leads to the low proportion of plate printers

the main production area of plate printing machines is mainland China, which is most obvious in Jilin Province. All plate washing machines in this region are mainland equipment. However, in Beijing, the proportion of European, American and Japanese products is relatively not low, reaching 24%; 18% in Hebei; Followed by Tianjin 15%. Different from the plate washing machine, the equipment in Taiwan, China also has a small share. Tianjin accounts for 10%, and both Beijing and Shanxi account for 5%

the linkage line of fully automatic printing slotting die-cutting gluing (nailing) boxes

the number of linkage lines of fully automatic printing slotting die-cutting gluing (nailing) boxes in North China is the highest in Liaoning and Hebei, followed by 16% in Beijing and 15% in Tianjin, and about 8% in Heilongjiang, Jilin and Shanxi

the proportion of producing areas of the linkage line accounts for 75% in Liaoning, Europe, the United States and Japan, and 45% and 40% in Beijing and Tianjin. Although the proportion of other provinces is slightly smaller, compared with other equipment, the proportion of European, American and Japanese products is also far ahead. The reason for this phenomenon is that the automatic printing slotting die cutting gluing (nailing) box linkage line is a high-end product with high price, so the absolute number of provinces and cities is small. When purchasing equipment, enterprises tend to invest in place at one time. Instead, they will buy European, American, Japanese or Taiwan, China products that are expensive but of good quality

the proportion of linkage linear speed is 1 o0 ~ 200 pieces/minute, of which the highest is 76% in Liaoning, and most of the other provinces and cities float up and down at 60%. More than 200 pieces/minute also account for about 44% in Beijing and Tianjin, because the import linkage line is of good quality and fast speed. The proportion of color groups in North China is balanced, with 3-4 colors. This is very different from East China and South China. The startup rate of the linkage line remained at about 75%, only slightly higher in Beijing and Tianjin, reaching 81% and 79%. Generally speaking, although the startup rate of the linkage line in North China is lower than the average startup rate in South China by 70% ~ 80%, it is higher than that in East China by 60% ~ 70%, which is in the middle of the national linkage line startup rate

printing slotting die-cutting machines

the proportion of the number of printing slotting die-cutting machines is the highest in Hebei, accounting for 21%, followed by Tianjin, 18% and Liaoning, 15%, followed by Heilongjiang, 13%, Beijing and Jilin, both of which are 12%, and Shanxi is the least, accounting for only 9%. Hebei is the production base of packaging machinery. Many other mixtures can be produced and sold by itself as few as possible. Most of them have been sold before leaving the province. Therefore, the number of printing and slotting die-cutting machines ranks first in the whole North China

printing slotting die-cutting machines are mainly produced in mainland China, accounting for 95% of the total in Heilongjiang, Shanxi and Jilin. In Hebei, Tianjin and Beijing, Taiwan, China's products account for about 35%, while Europe, the United States and Japan account for only a few single digits in this region. This shows that the total number of printing slotting die-cutting machines in this region is small, and the relative share is high

the speed ratio of the printing slotting die-cutting machine is less than 100 sheets/min. only in Liaoning Province, the speed ratio of 100 sheets/min to 200 sheets/min can reach 35%, and in Tianjin and Hebei Province, the speed ratio of more than 200 sheets/min is still 10%. Compared with South China and East China, the overall speed level of printing slotting die-cutting machine in North China is low

Copyright © 2011 JIN SHI